Command and Conquer: Renegade Official Forums: Mod Forum » Playing Manual Vis Points For Flying Maps

Home » Renegade Discussions » Mod Forum » Playing Manual Vis Points For Flying Maps

Show: Today's Messages :: Polls :: Message Navigator

Playing Manual Vis Points For Flying Maps [message #24225]

Mon, 09 June 2003 14:34

Sanada78
Messages: 435
Registered: April 2003

Karma: 0

Commander

So far all the Vis on my map is going fine, the only problem is for flying vehicles. When you fly high up out of the base too the battlefield, half of the terrian is missing unless you go down too the ground and it appears again like it should. The thing is I can't place manual Vid points high up over the map as them seem too have to be close to an object. When it doesn't work it says, "Vis Sample Rejected - No Vis Sector or Vis Sector ID not assigned!" in the comment box.

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24227]

Mon, 09 June 2003 14:44

YSLMuffins
Messages: 1144
Registered: February 2003
Location: Moved a long time ago (it...

Karma: 0

General (1 Star)
Moderator - Mod Forum

When it comes to the case of flying maps, you have to make "layers" of VIS sectors. Search for my VIS post.

Or give me a second and let me find it...

-YSLMuffins
The goddess of all (bread products)
See me online as yslcheeze

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24229]

Mon, 09 June 2003 14:47

YSLMuffins
Messages: 1144
Registered: February 2003
Location: Moved a long time ago (it...

Karma: 0

General (1 Star)
Moderator - Mod Forum

http://www.n00bstories.com/renforums/viewtopic.php?t=1223&postdays=0&postorder=asc&start=25

-YSLMuffins
The goddess of all (bread products)
See me online as yslcheeze

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24235]

Mon, 09 June 2003 15:16

Sanada78
Messages: 435
Registered: April 2003

Karma: 0

Commander

So I basically I have too sandwich layers of planes on my map and set them to "Vis"? Will I also have to separate them into smaller pieces?

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24237]

Mon, 09 June 2003 15:29

YSLMuffins
Messages: 1144
Registered: February 2003
Location: Moved a long time ago (it...

Karma: 0

General (1 Star)
Moderator - Mod Forum

Ideally, yes. The VIS layers should be separated by 10 meters.

-YSLMuffins
The goddess of all (bread products)
See me online as yslcheeze

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24238]

Mon, 09 June 2003 15:32

Titan1x77
Messages: 1086
Registered: February 2003

Karma: 0

General (1 Star)

Yes...Just make it so many segments and then explode them or manually seperate them.....prob segments the size of a building.

Havent done a flying VIS map yet....But I'd assume you'd do something like that.....From what ive seen of your map have about 30-40 secotrs on each side of the mountain 10 meters apart from each other....

Read The new renhelp....it tells you to name it Vis_Emis and export to your level folder.

Each layer should be broken into 70-80 sectors...or more Depending on how big the map is....My last map which was small had 400 total...From top to bottom...but it wasnt flying...it had moutains and tunnels that needed sectors..

If your map is flat....just clone all the terrain and raise it every 10 meters...Everywhere your gonna fly.

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24243]

Mon, 09 June 2003 15:50

Sanada78
Messages: 435
Registered: April 2003

Karma: 0

Commander

I don't understand how you explode an object. Will this separate a complete plane into its separate polygons? I've tried it but it doesn't seem to do anything.

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24250]

Mon, 09 June 2003 17:37

YSLMuffins
Messages: 1144
Registered: February 2003
Location: Moved a long time ago (it...

Karma: 0

General (1 Star)
Moderator - Mod Forum

How did you make the VIS sectors for your base terrain? Manually separated them? To explode, you have to set the parameter thing to 0, but this gives you a WHOLE lot more sectors then you would need (explode set to 0 splits up the entire meshes into separate triangles). I recommend just chugging through it and separating manually for your base terrain, and clone square planes for your VIS sectors every 10 meters up. Cloning terrain would slow things down a bit, with all the extra polys.

If anyone here can get explode to work correctly, ie, splitting meshes up according to POLYGONS and not FACES please post.

-YSLMuffins
The goddess of all (bread products)
See me online as yslcheeze

Report message to a moderator

Playing Manual Vis Points For Flying Maps [message #24255]

Mon, 09 June 2003 18:20

Sanada78
Messages: 435
Registered: April 2003

Karma: 0

Commander

Okay, I did do my terrian that way so I guess I'll do it the same way for the Vis sectors. Thanks.

Report message to a moderator

Previous Topic:	JFW_Building_Gun
Next Topic:	---::::: To All Mod Teams :::::--- (added link to Renders)

Goto Forum:

-=] Back to Top [=-

[ Syndicate this forum (XML) ] [

] [

]

Current Time: Thu Dec 26 06:47:42 MST 2024

Total time taken to generate the page: 0.00848 seconds